Omnipure K2586 BB GAC/Phosphate Scale Inhibitor Female NPT 1/4"

Omnipure K2586 BB GAC/Phosphate Scale Inhibitor Female NPT 1/4"
Omnipure K2586-BB Inline Icemaker GAC CTO/Scale - 10 x 2 1/4 FPT Filter

More details

On sale! FREE DELIVERY ON OVER $100 Total Price: $35.00 tax incl. Each: $35.00 tax incl.

RRP : $89.00 each tax incl.

You save: $54.00 (61%)

K2586 BB

Add to cart

Share This Page!

Average votes for this product

Average : 0 / 5
Based on 0 customers advices.



Omnipure K2586 BB GAC/Phosphate Scale Inhibitor Female NPT 1/4"


Omnipure K2586-BB Inline Icemaker GAC CTO/Scale - 10 x 2 ¼ FPT Filter Features:

The Omnipure K-Series K2586-BB inline filter is a GAC phosphate filter. This filter has 1/4" NPT that make the filter really easy to install and replace. This filter can go in ice makers, refrigerators, beverage equipment, drinking fountains. The Reverse Osmosis Systems work with purification systems to provide to purest drinking water possible. The K2586-BB removes bad taste, odor and chlorine. along with 6 ounces of polyphosphate scale inhibitor.

  • Capacity: 1,250 gallons
  • Life Cycle: 6 months
  • Scale Inhibitor: 6 oz polyphosphate
  • Filter Dimensions: 10" x 2"
  • Connections: 1/4" FPT
  • Flow Rate: 0.50 GPM (1.9 LPM)
  • Maximum Pressure: 125 PSIG
  • Temperature: 35-100°F (2-38°C) 


Flow Rate

0.5 gpm

Maximum Operating Pressure

125 psig

Operating Temperature

2 to 38 ºC35 to 100 ºF

Rated Capacity

1,250 gal (Scale 6 Months)

Reduction Claim

Chlorine, taste, color, and odor reduction with scale/corrosion inhibitor

Flow Capacity

1,250 gal


ANSI (American National Standards Institute)NSF (National Sanitation Foundation)

ANSI (American National Standards Institute) / NSF (National Sanitation Foundation) International Standards

Tested and Certified by NSF International against ANSI / NSF Standard 42 for Taste and Odor Reduction and Chlorine Reduction Class I.


General Installation / Operation / Maintenance Requirements

  • Note flow direction of filter.
  • For quick connect fittings, push scratch free tube end into the fitting until it bottoms. Threaded fittings must be wrapped with PTFE tape before installation. Install PTFE taped fittings and tighten firm. Use two wrenches to firmly tighten tubing.
  • Flush new cartridge with 5 gallons of water prior to use and check for leaks. If leaks occur, check tightness of tubing and fittings. If leaks persist, discontinue use and call your supporting dealer.
  • Replace cartridge when rated capacity (1,250 gallons/1 year) is reached, or when flow becomes too slow.
  • Install in compliance with state and local laws and regulations.

Special Notices

  • The contaminants or other substances removed or reduced by this water treatment system are not necessarily in your water.
  • Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

Manufacturing Notes

The scale inhibiting properties of polyphosphates are affected by the chemistry of the water being treated and will vary. Thus, no performance data is available.

Additional Information

Cap and body are spin welded together producing a smooth, consistent seal without the use of glues or binders that can cause contamination. The result of these design and production techniques is a reliable filter that is fast and easy to install.

One of the primary uses of this product is as a system component. The benefit is derived from the fitting being molded directly into the filter cap, greatly reducing clearance. Shown here (right) is a reverse osmosis system with the traditional 12 in x 2.5 in filter configuration. Notice that all the filters are uniformly attached. This results in the most efficient use of available space and greater filtering performance in a smaller overall area.

The K-Series filter is available in 6 in, 8 in, 10 in, 12 in or 14 in lengths manufactured in 2 in or 2.5 in diameters. The true benefit is that systems can be designed to incorporate the various lengths and diameters - either all the same size or intermixed - to meet specific filtration needs.

Water filter heads sold separately.

Also Compatible With: Pentek TS-101L, 155083-06, GS-10ALS-B, 255595-43

Straight Adaptor – Nptf Thread

PP010821W 1/4" 1/8"
PP010822W 1/4" 1/4"
PP010823W 1/4" 3/8"
PP010824W 1/4" 1/2"
PP011222W 3/8" 1/4"
PP011223W 3/8" 3/8"
PP011224W 3/8" 1/2"
PP011623W 1/2" 3/8"
PP011624W 1/2" 1/2"



We aim to provide you with the best price available in Australia! If for any reason you find a better genuine online price, let us know where and we will match it. Just email: info@waterfilterforfridge.com.au  (please allow for freight component)





 we are the cheapest fridge part dealer in Australia




More  inquiry about this  filters?  Call  us  1300 767 072 or Email us sales@waterfilterforfridge.com.au







We would like to hear your experience using this product. Your feedback helps us to improve our products quality & continue providing great products. We really appreciate that!


Please log in to leave new review | Log in

No reviews at this time.

Omnipure K2586 BB GAC/Phosphate Scale Inhibitor Female NPT 1/4" (35 AUD )